Bridge Converter Module
IDM-16E1 Digital Intelligent Distribution Frame
16 groups of E1 full cross-connection, dual-fiber ring network protection, power failure pass-through, services uninterrupted
The IDM-16E1 digital distribution frame is a 16-group E1 full cross-connection device providing intelligent configuration and power failure pass-through. It implements 16 groups of E1 channels with a simple board structure. The IDM-16E1 provides a network management interface, supports power failure pass-through and power failure memory, and features complete alarm monitoring, high integration, low power consumption, stable performance, and ease of use. The IDM-16E1 digital distribution frame provides complete alarm monitoring. Alarm content includes loss of E1 signal and out of frame (OOF). In addition to reporting local alarm states, it can also display the alarm state of the opposite end via the local indicator LEDs using a button.
View Details →
IDM GE Aggregation Bridge
63 E1 channels in 1U, single STM-1 mapping of 63 channels, compatible with multi-vendor E1 networks
The IDM GE/STM1 multi-channel aggregation bridge is an intelligent aggregation bridge developed by our company to meet customer demand for high-capacity Ethernet leased-line access in the market. It can aggregate 63 E1 channels into gigabit Ethernet and directly interface with SDH transmission equipment.
View Details →
IDM OPT-16AM Industrial-Grade 16-Channel Analog Optical Multiplexer
FPGA parallel 16-channel no queuing, single-fiber synchronous relay, latency <0.1ms per channel
The IDM OPT-16AM device adopts a large-scale FPGA design and proprietary technology to simultaneously support 1 to 16 channels of analog signals (current/voltage) relayed over optical fiber. The device uses dual power supply, a high-performance FPGA programmable device with no MCU processing, high-speed conversion, a sampling frequency of up to 20KHZ, and a 12-bit AD conversion chip. It solves the challenges of electromagnetic interference, ground loop interference, and lightning damage, greatly improving the reliability, safety, and confidentiality of control signals, while also resolving the limited transmission distance of cables.
View Details →
IDM OSN-2GE Network Channel Monitoring and Switching Device
Optical Fiber + 4G/5G Dual Backup, Fault Switchover ≤500ms, Bandwidth over 90% in Advance
One second of communication interruption can halt financial transactions, disconnect power monitoring, or break emergency command—in critical service scenarios, communication reliability is always a red line that must not be crossed. The IDM OSN-2GE network channel monitoring and switching device is purpose-built to address communication pain points in critical scenarios. With four core capabilities—redundant backup, intelligent switching, convenient O&M, and secure control—it safeguards communication reliability in the energy, financial, and industrial sectors.
View Details →
IDM E1/FE Bridge
Dual power supply, low power consumption, DIP-switch tool-free configuration, centralized with remote network management
The IDM E1/FE Bridge is designed with large-scale dedicated integrated circuits and implements inverse multiplexing of Ethernet data onto one E1 channel or an optical fiber. The device is available in centralized and desktop models; the centralized device provides 1 Ethernet interface, and the desktop device provides 4 Ethernet interfaces. The device supports two transmission modes: E1 and optical fiber. When the device operates in E1 transmission mode, the maximum Ethernet bandwidth is 2.048 M; when the device operates in optical fiber transmission mode, the maximum Ethernet bandwidth is 4.096 M. The device supports network management functions. The management device can manage the local end or desktop devices through the centralized device, and at the same time the centralized...
View Details →
IDM-E1/V.35 Protocol Converter
Dual mode: transparent E1 and arbitrary time slot partitioning; unused time slots reserved for other services; transmit phase
The IDM-E1/V.35 interface converter and IDM-FE1/V.35 interface converter can convert all or part of the E1 time slots (i.e., N*64K) into a V.35 interface, with bandwidth from 64Kbps to 2048Kbps. They can be widely used in computer network interconnection and DDN data network access.
View Details →
IDM GP-2400 Public Security and Armed Police Dedicated Network Converter
2 groups gigabit isolated
The Public Security and Armed Police Dedicated Network Converter can transmit 2 groups of physically isolated wire-speed gigabit Ethernet and 4 groups of wire-speed physically isolated 100M Ethernet over 2.5G optical fiber. It provides 2 groups of 2.5G optical fiber hot standby. It can simultaneously provide ~220V and -48V power supplies.
View Details →
IDM OPT-E1 Optical Modem
Interoperable with single E1 bridge optical port; desktop dual power supply ≤5 W; star capacity expansion by adding remote units
The IDM OPT-E1 optical modem has a desktop form factor. Each unit provides an E1 transmission channel over optical fiber, including clock extraction and transmission. It can interoperate with the optical port of a single E1 bridge and can easily form a star network with centralized optical modems. The device supports dual power supply of AC 220 V and DC -48 V and can be used in various fields such as LAN interconnection, video on demand, and remote monitoring.
View Details →
IDM-RACK3U Centralized Protocol Converter
17 remote ends aggregated in one chassis, eight types of service cards mixed insertion, single board failure swap without service interruption
The centralized protocol converter adopts a 19-inch 3U front-loading card-based structure. Each card corresponds to one remote RS232/422/485 data optical multiplexer or single-E1 bridge (optical modem), E1 optical multiplexer, high-speed serial optical modem, fiber optic switch, serial-to-bidirectional HDMI converter, telephone optical multiplexer, or E1 (V.35) optical modem, and can easily form a star network. The IDM-RACK3U centralized protocol converter makes full use of the large amount of existing E1/optical fiber resources in telecommunications networks to extend the transmission distance and application scope of Ethernet, providing a better solution for Ethernet access. This product can be used in local area
View Details →
IDM-RACK5U Centralized Bridge
5U front-card mixed insertion saves rack positions; one card supports two remote ends, up to 32 channels at full configuration; card replacement without removing the unit
The IDM-RACK5U centralized bridge is a rack-mounted, small-capacity multi-user access network platform system designed for star network topologies with large-user access. It offers high integration and strong compatibility, and can be flexibly configured with different quantities and types of
View Details →
IDM STM-1 Optical-to-Electrical Converter
One optical and one electrical port in a standalone unit completes 155M optical-to-electrical conversion, eliminating the conversion chassis and secondary wiring
The IDM STM-1 Optical-to-Electrical Converter is a new-generation product developed by our company based on SDH technology with independent intellectual property rights. It provides interface conversion from an STM-1 (ATM) electrical interface to an STM-1 optical interface. The STM-1 (ATM) optical-to-electrical converter completes the transmission of STM signals over SDH, or 155M SDH optical-to-electrical conversion, and is suitable for interconnecting various data terminal equipment with 155.520 Mbps interfaces, such as SDH and ATM equipment. Its design follows the ITU-T and Ministry of Information Industry of China specifications on SDH.
View Details →
IDM STM1/GE Central Office EOS Network Bridge
63-channel EOS standalone aggregation saves 63 2M conversion devices dual STM-1 1
The basic function of the IDM STM-1/GE is to demultiplex the Ethernet frames arriving at the GE port into different flows (using the MAC address, VLAN TAG and other information carried in the Ethernet frames themselves), then encapsulate the Ethernet frames of different flows into GFP frames (forming an EoS signal), and then map the GFP frames into different VCGs (each VCG can contain 1 to 63 VC12 channels);
View Details →
IDM STM1 Bridge
63-group E1 arbitrary partitioning, 4-channel 100M physically isolated, single unit directly connected to SDH to save one level of coordination
The IDM GE/STM1 is an intelligent aggregation bridge developed in response to customers' high-capacity Ethernet leased-line access requirements. It can aggregate 63 groups of E1 into gigabit Ethernet and directly interconnect with SDH transmission equipment. Channels 1 to 63 can be arbitrarily partitioned according to different bandwidth requirements, and Ethernet data is transparently carried with each channel as a link unit.
View Details →
IDM TRX-8E1net Bridge
8-channel E1 inverse multiplexing, asymmetric receive/transmit channel counts, 220 ms delay difference tolerance
The IDM TRX-8E1net bridge is a protocol converter independently developed by our company using inverse multiplexing technology. The device bundles multiple E1 lines to transmit 10M/100M Ethernet data, converting between 8 E1 channels and Ethernet interfaces, with a maximum Ethernet transmission bandwidth of up to 15.84M.
View Details →
MPC8309 Core Board Module
Three SoCs interchangeable on the same baseboard; dual gigabit Ethernet ports and RS485 full-duplex shipped with the board; schematics provided
Available for order on freescale.com Schematics, Gerber files and user guide provided Will come with Linux® BSP & drivers MQX port will be available mid-August 2010 MPC8308, MPC8306 and MPC8309 SOMs a
View Details →
IDM OSN-2GE Network Channel Monitoring and Switching Device
Redundant backup, intelligent switching, convenient O&M, switchover ≤500ms (no data loss)
One second of communication interruption can halt financial transactions, disconnect power monitoring, or cut off emergency command—in mission-critical scenarios, communication reliability has always been a red line that must never be crossed. The IDM OSN-2GE Network Channel Monitoring and Switching Device is purpose-built to address the communication pain points of critical scenarios. With four core capabilities—redundant backup, intelligent switching, convenient O&M, and secure control—it serves as the guardian of communication reliability in energy, finance, industrial, and other sectors.
View Details →
IDM OSN-5GE Emergency Multi-Link Aggregation Device
5 Gigabit WAN Redundant Backup, Millisecond-Level Switching, Bandwidth Stacking, Single-Port Output, Domestic Chip
The IDM OSN-5GE route link management device adopts a 19-inch 1U standard rack-mounted design and is a multi-link aggregation core device purpose-built for emergency communications scenarios. Centered on "redundant backup + intelligent scheduling + bandwidth aggregation," it integrates multiple communication paths, monitors link status in real time, and enables priority-based intelligent switching and multi-channel bandwidth stacking. It adapts to satellite, microwave, SDR mesh, and other communication scenarios, providing stable, efficient, and secure communications assurance for emergency command and disaster rescue in extreme environments.
View Details →
IDM-OXC Optical Cross-Connect Equipment
48-core non-blocking cross-connection, patching ≤3 minutes, power-off pass-through, insertion loss ≤1 dB
The IDM-OXC optical cross-connect equipment is an optical path control device that performs arbitrary non-blocking cross-connections and interconnection between multiple input optical ports and output optical ports. It offers advantages such as a small footprint, fast switching speed, and high operating reliability. In optical communication, it is mainly used for intelligent fiber scheduling at nodes, multi-dimensional online monitoring, multi-route service protection, and optical fiber equipment or network testing.
View Details →
IDM-OXC Optical Cross-Connect Equipment
48-Core Non-Blocking Cross-Connection, Patching Time ≤3 Minutes, Power Failure Service Pass-Through, Intelligent ODF Management
The IDM-OXC optical cross-connect equipment is an optical path control device. It performs arbitrary non-blocking cross-connection and interconnection between multiple input and output optical ports, and features compact size, fast switching speed and high operating reliability; in optical communications it is mainly used for intelligent fiber scheduling at nodes, multi-dimensional online monitoring, multi-route service protection, and optical fiber equipment or network testing.
View Details →
IDM-RFlabel Intelligent Optical Fiber Distribution Frame
48-port port-by-port RFID monitoring, red light alarm on misinsertion, tri-color LEDs eliminate record checking
The IDM-RFlabel intelligent optical fiber distribution frame is typically used for the management of equipment room ODF optical fiber distribution frames. It usually works with the equipment room cable database. RFID tags are affixed to the ends of optical cable distribution frames in the equipment room, and the devices and port numbers connected to each cable and optical cable are recorded in the database. RFID monitoring antennas are affixed to each corresponding port on the ODF distribution frame. If a fiber optic cable or cable head insertion is detected, the database is checked to see whether it is the required line; if not, an alarm is triggered. Each port is equipped with a corresponding indicator LED: red indicates an error, green indicates normal, and off indicates no connection.
View Details →
IDM-RFlabel Intelligent Optical Fiber Distribution Frame | Intelligent ODF | RFID Optical Fiber Distribution Frame | Optical Port Status Monitoring | Equipment Room ODF Intelligent Management
IDM-RFlabel Intelligent Optical Fiber Distribution Frame | Intelligent ODF | RFID Optical Fiber Distribution Frame | Optical Port Status Monitoring | Equipment Room ODF Intelligent Management main product image
Passive RFID Tags Need No Battery; Tri-Color Indicator LEDs Show Right or Wrong at a Glance; Scanning Stops When the Equipment Room Is Unattended, Without Disturbing the Network
View Details →
IDM VoiceCable Online Monitoring Equipment
30-channel telephone line online monitoring, power failure pass-through without call interruption, line break and short circuit fault location
The IDM VoiceCable online monitoring equipment is an equipment room service platform for online monitoring and management of telephone cables. It was used in early 112 online testing services in equipment rooms and is now mostly used for telephone line monitoring in private network communications equipment rooms. Test items include line breaks, mixed lines, poor insulation, cross-voltage, and noise. This device is used for manual or automatic testing in private network equipment rooms. It records line status. The device performs corresponding parameter tests on lines according to the configuration. Testing can be automatic or manual, with various telephone test audio output modes and test modes, and a test telephone interface. The system transmits test data in real time
View Details →
E1/V.24 Interface Converter
4-channel E1, 8 ms delay difference tolerance, automatic disconnection and recovery at both ends on line break, power consumption <5 W
The TRX E1/V.24 interface converter converts between a transparent E1 transmission channel and a V.24 interface. It is widely used in data communication equipment and is suitable for connecting V.24 devices over optical fiber, microwave, DDN private networks, or other 2M channels.
View Details →
Serial Port Server Module
RS485 RS232 to Ethernet Integrated Plug-in Card Virtual Serial Port No Software Modification Required
Serial port server module. Beijing Ruiguang Jiyuan Digital Technology Co., Ltd. provides technical specifications, selection recommendations, networking approaches and supporting application solutions for this product, with support for customized development and on-site technical support.
View Details →- 1